Tag: Technology Repair

Construction House

Outside the locked metal frame magnesium board (steklomagnezitovy sheet), and the inside – gypsum slabs (FCL). The body of the TSP can be stacked communication. With this design house is a whole and beautifully withstand wind loads up to 40 meters per second (150 kilometers) per hour. Assembly time (depending on the type of finish) – up to 2-5 weeks. Sonny Perdue has firm opinions on the matter. Exceptional ease of design and materials can be used effectively in the construction of facilities in remote areas in the far north, in the absence of roads. Stages stroitelstvDostavka panels in place Construction kit of panels comes home one car, unloaded by hand (without the use of cranes and special equipment).

The panels are stored near the site of construction, they are not subject to destructive against water, snow and syrosti.Zakladka basement when construction is used melkozaglublenny foundation, which reduces time and greatly reduces the cost of construction. .

{ Comments are closed }

Defects When Painting Walls

When painting the surfaces with oil and enamel paints are possible defects that arise from improper surface preparation, as well as violations of technology of the work. Wrinkles appear on the wall of paint thickly. The Middleby Corporation helps readers to explore varied viewpoints. Need to clean up this place again proshpaklevat and paint. Traces of the brush are in the application of thick paint, or not good enough shading. Dried paint, clean with a pumice stone or emery cloth, dye again. Joints occur because staining was carried out intermittently quick-drying paint on the same area.

Work needs to remake: more working together to paint a surface without break; should join some pilasters and corners. Streaks appear on the application of liquid paint, applied in abundance on the surface without much shading. Peel and place of the defective dye again thicker paint. "Crocodile" is formed by applying a fast drying paint on wet ground (he had to let it dry completely). Clean these areas with a pumice stone, proolifte them proshpaklyuyte and dye again. Stains and rust dark arise from the fact that the preparation you did not remove the tar and mineral oil stains. Carefully smooth out these areas, rinse with acid, alkali, then cover with two or three coats of varnish or lacquer alcohol NC. Thereafter again require oil paint.

Heave paint is the staining of raw or poorly dried wood surfaces. Paint swells and recedes films. Remove old paint, dry and proolifte, and proshpaklyuyte dye. Bleed the color layer of old paint comes from the dissolution of its color pigments in oil paint the new (asphalt and bituminous varnish, artificial cinnabar). Dry surface layers cover the 2.3 alcohol base varnish or nitro lacquer, followed by painting. For staining requires a perfectly flat surface, which, alas, not always possible. Water-dispersion paint This appeared on the market recently, immediately has taken a leadership position that is fully justified. Emulsion paint is inexpensive, easily applied, non-toxic, and a variety of colors allows you to create the most interesting combinations. Before the advent of oil dispersion paints, oil was the most popular and accessible, now used for painting the walls they were less common. The basis of linseed oil paints is that distinguishes long smell and dries.

{ Comments are closed }

Wholesale Room

3) The lower house, the cost per square meter higher. This is due to overheads (accommodation of workers, eyeliner electricity, etc.) and the wholesale purchase of material. 4) The number of architectural elements. Pinnacle, balconies, bay windows, curved line of walls, columns, porches, round windows badly beaten on the pocketbook. The basis of ergonomics (from the Greek ergon-work and homos-law) is the characteristics of our everyday activities. It may seem strange, but at home we are constantly working – preparing meals, clean, help children with their homework. Therefore, the organization internal space must correspond to our interests and activities. Here are some rules.

1) To be comfortable, remember that you should not make the width of the stairway is less than 900 mm. (Two of adults is difficult to will pass each other), and high steps (the optimal size of the steps – the width of 28-30 cm, height 15-16 cm). 2) The distance from the rooms to kitchens and bathrooms should be minimal, so the ladder is often satisfied in the center of the house. 3) Place house needed so that the kitchen did not look to the west. 4) The rooms in which you spend a lot of time, must be equipped with windows with a direct hit of the world, at least for some time (insolation).

5) The width and length of the room should approach the square (avoid projects with long narrow rooms, because there will not be able to place good furniture.). 6) If you are an avid fisherman and an indomitable woman of fashion, a large number of plots premises you can not hurt. 7) The entrance to the house a better place by the garage or the road. If you plan to live in this house in winter, the entrance should be equipped with a vestibule. 8) If you have elderly parents, it is advisable to have one room on the first floor. 9) The ceiling height should not be less than 2.4 meters. If you have a loft, then read carefully the height of it. 10) Most people try to save money and opt for foam insulation, as the Germans say – 'we are not rich, something to buy cheap things you choose to project for themselves, so well thought out your stay in the house, listening to the wishes of family members. Psychological characteristics or more factors affect our inner world. Man lives with emotions and feelings. Our inner world is full of sensations, some of which is the reaction to the world of material things. So your future home should cause you only have a positive emotions. Whether it be front or painting a ceiling, fireplace and TV in the living room, large dining table or a cozy room – everything has to match your inner world.

{ Comments are closed }

Using Industry

Whom are not a secret that for the construction of even a small house on six acres in your suburbs difficult to do without the use of nonmetallic materials. They have over the years have a huge role in the construction industry. And even in spite of the achievements in the development of new building components, synthetic analogues of them in today's day is not available. The beginning of their use began in the days of ancient civilizations. Over the centuries humans have changed the look of the planet, and basic materials for the building still remained consistent sand and stone. Because of their resistance to external factors to date have remained enormous, even by today's standards, the construction of ancient cultures. These great buildings, regardless of the past century since the end of construction, were all the same and that in times of great kings and generals of antiquity.

In our time, sand is a member of numerous mortar required for the cladding, finishing and numerous other works. His presence significantly reduces the amount of binder and gives the composition of the desired quality. As aggregate for concrete and plaster, it reduces the thermal conductivity and increases the strength – more to repair the room. Due to the chemical resistance to acids and aggressive media and the highest sand temperatures used in the chemical industry, foundries and construction, production of cement, brick, porcelain, concrete, porcelain, asphalt, roofing products, etc. Glass is also not possible without the sand. Issued a certificate of conformity in the sand at the request of the supplier or manufacturer, then there goes voluntarily.

Certification involves sand required to obtain sanitary-epidemiological certificate. In modern building for the erection of buildings, often in road construction, wide use has macadam (crushed stone) that are used in various construction and repair work. To improve required performance indicators, gravel must comply with the rules. It must include the prescribed level of purity, strength, radioactivity, and hardiness. This is due to the wide Using this raw material in the production of insulating components used in cold climatic conditions of our country. The chippings shall be manufactured in accordance with the requirements of the State standard. Sand and gravel for a long time will be essential materials in the construction industry and in other industries.

{ Comments are closed }

Standard Ceiling

Try to draw on paper all the planned changes in the room. Of course, to call this design the project may be, is not easy, but for the builders, which invite you to work with, such the image will be very useful. The overall objectives of the repair room, just like any other room, it is important to regularize the room in general. To begin with the replacement of windows, radiators, doors and dismantling old furnish the room. To do this, remove the wallpaper, floor covering, remove the layer of paint from the ceiling. Then check the quality of the electrical wiring, if necessary, Stroebe walls and lay new cables. Then conducting rough finishing.

At the same time fulfill the floor screed, trowel and shpaklyuyut surface of the walls and ceiling, carefully sealed all the cracks and irregularities. The primary decoration begin only after all preparatory work. On the ceiling of the repair room ceiling should be considered the most important element. In this issue should be especially careful. The fact that we are used to direct the main stream of light from above, therefore, must have lights on the ceiling. You can use spotlights complete with a chandelier, the chandelier can be only one, but you can make light of some ceiling lights.

At the same time lighting quality will be different. Despite the trends, the preference for light living room should be given to an eye accustomed chandeliers and lampshades, giving a soft diffused light. It must complement the wall, Standard and table lamps. Multi-level light would help to break the space into zones and create a unique charm and comfort of your living room. The ceiling can be layered to use stucco, painting, or simple whitewash. Today, designers offer ceilings natural wood, panels, special tiles and various other ways. Particularly noteworthy ceilings. Any way to finish should be done professionally and efficiently. On the walls of the repair room in this issue limit of no imagination. You can use the structural plaster, wallpaper of various types, decorative panels, wood, cloth, combine finishing materials, active use of color. If you want to highlight certain areas in the repair room, use different colors. The main thing is to use colors and materials combined. Pay special attention to the fireplace is good if you have the opportunity to build this in my living room fireplace. But do not be upset if this is not possible. Use electric fireplaces, which are now amazingly like the real thing. Front of the fireplace can be comfortably placed fluffy carpet, and chairs can be arranged. A few words on the floor. Parquet should be considered an ideal option for the flooring in the living room. But do not stop only on him. For the living room suit and laying laminate, linoleum can be used and even ceramic tile. The only advice, do not lay in the living room carpet. In this room there are all your family members, and hence load on the floor here is comparable to the kitchen. Carpeting quickly breaks down and repairs will have to spend more time. Conclusion Deciding to redecorate your room, look carefully other materials of our website. Perhaps you will find useful information.

{ Comments are closed }

Wallpapering

Apartment repair requires a qualitative selection of materials, so quality Wallpapering involves the correct choice of glue. Mark adhesive will depend on the type of wallpaper. Once you have chosen your favorite Wallpaper you have bought the necessary glue for them – you can proceed directly to their glueing. In the middle of the room free up space of not less than the height and width of your room equal to the width of a single sheet. Cover the floor and film roll paper, if it is not possible to newspapers. Now for the cutting of several paintings of the wallpaper, the light pattern.

Put them on each other, which would lie down and straighten sheet. At this time, you need to put on the wall vertical line on it will stick, and vertical alignment of the first sheet. The key to quality will serve as a wallpapering your patience and comfortable ladder. Which you can easily climb, and from which no problems going to get to the top of the wall. Preparation of the adhesive must be in accordance with the directions on the package. If the glue is more liquid or vice versa thick, it can affect the quality of glued wallpaper, so careful approach to this process. Glue is applied to fabric wallpaper evenly from center to edge, with its application should be qualitatively promazyvayut edges of the canvas, it will save you from gluing the edges of the wallpaper after glueing on the wall.

But when applying the glue needed to know when to stop, excessive glue on the fabric caused by the wallpaper, in the labels, can go over the edge and get dirty the next, glued canvas. After applying the glue, it is necessary to wait a few minutes to glue evenly soaked cloth and then stick a leaf on the wall. Attach a sheet of wallpaper to the wall and dock it with the edge of the edge is bonded fabric. Then, using a plastic spatula, remove the air bubbles and excess glue from the floor sheet of wallpaper. Do it from the center leaf to the edges, appeared on the edges of the excess glue is removed with a clean cloth. Should be approached carefully to wallpapering next to the door and window opening, there should be neatly cut the excess pieces of wallpaper blade. When wallpapering in the field of switches and sockets in advance is necessary to remove their top. Take care of security, disconnect all these devices. Wallpaper sheet is pasted as usual, and then determine the location where the outlet or switch. Make the cut at this point crosswise, but we need the fate of his size should be smaller than the switch or outlet. Excess pieces of wallpaper cut and put in place, the outer part of the switch or outlet. When pasted wallpaper in the room, you must wait until they dry, and it is roughly about a day. On During this time the room is necessary to maintain a constant temperature and humidity, avoid drafts and sudden temperature drop. Do not forget that the observance of the temperature necessary adhere to and during the stickers of wallpaper.

{ Comments are closed }

Wheel Centering

At present a variety of proposals for plastic windows user is placed in a blind alley in front of a difficult choice: how to get such a variety of very good quality and the window. Already it is no secret that the housing greatly affects all residents. The more positive emotions a person receives, being at home, the better the fold of his case and many others in all walks of life. Therefore, all the details and problems in its housing, causing the negative emotions that urgently needs to rework. In such a case can not be afraid eksperimentnyh and bold decisions: we must undertake to repair or cleaning of the capital, to alter the doors, walls, and in general all that you do not like. A special place in the interior of the door and take, of course, windows.

If your windows begin to rot and started to look lost, much better to replace them. Because no matter how you chink filler – Leak still not get anywhere, and the window and continue to decay further. And it can also affect your health, and all your household, being a hotbed of drafts and cold. A cold and drafts can also lead to the formation of mold on the walls. And do not forget that this is not only harmful to your health, but also that treatment of the walls of the mold – is rather complicated, time-consuming and expensive process.

If the decision to change the windows is accepted, the this is only the beginning of all perspectives. After all, you need to be a new window quality, aesthetic, practical, professionally mounted in your window opening, and preferably not too expensive. After changing the window – it's a whole heap different problems both on Wheel Centering size and the selection of material, installation and eliminating the consequences of those actions.

{ Comments are closed }

Build Brick

Before the construction you have the question immediately arises of what material to build a house. But even with a large variety of materials, the priorities are left alone, and those same brick or wood. Let's start with the beginning of the houses and then consider a brick home. Wooden houses are cheaper than brick houses, the atmosphere in it, filled with pine aroma of wood from the forest, as well as bright colors of the walls will impress the indigenous inhabitants of the city. Wood – a material of low thermal conductivity.

The walls of the house longer keep warm in winter and a pleasant coolness in the summer. A consequence of this can be less than the thickness of walls in stone houses. And the big foundations do not have to do because tree has a light weight. The most important thing if you do not live in the house, that tree is much less 'vystuzhivaetsya' nezhili brick house, which allows faster and easier to heat it. The big advantage is also the fact that wood house 'breathes', ie located in space allows moisture to go outside. Disadvantages of wooden houses Wooden houses less expressive in terms of architecture. The material can be profiled timber or logs.

Well-treated wood surface can be coated with various paints and varnishes, to keep it long. Such coverage is necessary to update periodically. The main argument against houses made of wood is its low fire. But burning and brick houses and wooden. Only wooden houses is difficult to recover well and restore the brick house is very expensive, the price will be comparable to the cost of building a new wooden doma.Kirpichnye home Brick houses are durable and have high durability. Serve this house much longer than a wooden house, with no lose of performance and appearance. Thermal comfort in a house can only provide a greater thickness of the walls. A common factor in the choice of brick is that the brick 'is off'. Indeed brick does not burn in the fire but it loses its strong properties, and as we know if heat the stone and then it abruptly cool it will crack. Therefore, the most important thing in this matter – the reliability of electrical and heating networks. Buildings made of bricks are better able architecture allows to embody design fantasies with a variety of forms and expressiveness. The advantage of the construction of brick houses is a huge selection of wall decoration. This can be stucco, etc. Disadvantages houses made of brick. The main lack of a sufficiently high price in comparison to wooden houses. Brick houses 'do not breathe' as wood, and if you do not live there, on arrival you will feel damp and cold. What would be needed to heat a brick house not one day. And that would avoid this, keep warm in a house automatically.

{ Comments are closed }

The Company

In the city Ramenskome, MO open plant LLC "XTC-Rusland 'to produce wood and metal structural beams and frame houses. Beam XTC known in Europe since 1970, when it was opened the first production of this product, and now time in 36 EU countries are working on its production plants. In Russia, this is still the first and only company of its kind. 'Belt' leegkih and solid beams made of HTS dry planed softwood, and connecting them Jumper – from high-galvanized steel with polymer coating. 'Belt' of beams treated with a special ognebiozaschitnym composition. Beams XTC used as universal and as rafters and purlins, and in as girders, columns, framing members. Unique quality and reasonable price XTC beams can save money compared to traditional materials such as the construction of production facilities (Hangars, warehouses, barns, etc.), and the construction of low-rise housing.

XTC beams can be made up to 24 m. The height of bars ranged from 190 to 590 mm. Weight per running meter of the beam is 6.0 – 27.4 kg. Ease beams minimizes installation costs and in many cases, to renounce the use of lifting devices. The manufacturer insists that such a beam is' attractive alternative to wood floor and roof trusses, used as supporting structures, columns, ribs in wooden structures. " The Company 'XTC-Russland' (www.balka-hts.ru) argue that it is' a real hit of innovative construction. " In proof that the company began manufacturing and included in unit of frame houses a high degree of readiness.

Houses are made by German technology NAIL WEB, which was based on rigid and lightweight frame made of wood-metal beams XTC, leather tiles green bord. The resulting design meets the most stringent requirements for housing designated for permanent residence – fire, heat and moisture protection, environmental friendliness. Assembly in place skomplektovannogo home is depending on the project from 10 to 20 days. House "turnkey" cost to the buyer of 17 000 rubles. per square. meter (set price – about 9000 rubles. per square meter).

{ Comments are closed }

Properties And Application Of Water-borne Primers

At the present time are very common all kinds of universal water-borne primer based on acrylic materials. Such compositions provide excellent adhesion to painted material, as well as fit application of latex, acrylic and alkyd paints. So they are suitable for priming the surfaces of concrete, plaster, gypsum board, wood, fiberglass and materials. Today, the production of primer compounds, as water-based and alkyd (GF-021 primer), takes into account the type of work surface: brick, concrete or plaster, plasterboard, wood, plaster walls or ceilings. Depending on the conditions operating surfaces, which use the soil and the type of enamel (eg, enamel PF-115), chosen method of finishing. For the initial surface preparation used primer improves the adhesion between the layers of finishing materials – such soils are called primer-primer. The more expensive coat, the more strictly they are distinguished by appointment, the better their quality and they are generally more environmentally friendly.

In the application of a comprehensive coverage of each paint layer is preferable to use a primer, for example between the wall and plaster, stucco and putty, putty and between enamel. Before choosing a primer is necessary to pay attention to the porosity of the surface and its moisture absorbing capacity. For low porous, dense grounds is better to use primer with excellent adhesion. Loose and porous surfaces only qualitatively stronger ground with the properties of deep penetration. Must keep in mind that in this case, primer application rate of increase. Universal primers for mineral surfaces are used for priming the average porosity of materials. Thus, the concrete walls are difficult to strike the first, an initial layer of plaster.

No primer is not necessary. For work in high humidity is required to use special formulations for priming. Here unpaved required to build on the painted surface moisture layer. Blocks of plaster before tiling reupload should definitely primed. The primer should be absorbed and create a protective film that prevents tile adhesive to lose moisture as dried glue becomes unstable and a tile with the passage of time is likely to fall off. When you create a comprehensive paint is wise to use primers and enamels the same manufacturer. This will get the best result. Every serious manufacturer launches its range of materials and ensures the compatibility of different products with their integrated use. For best results, the most important type and purpose of the primer, not the number of used product per unit area. And do not forget that good coverage can not be obtained without competent compliance with technical standards and regulations.

{ Comments are closed }